![Vpc mac address learning](https://knopkazmeya.com/1.png)
![vpc mac address learning vpc mac address learning](https://www.exam4training.com/wp-content/uploads/2020/07/image006-20.jpg)
– see if timer is attached on the VLAN/vrf
![vpc mac address learning vpc mac address learning](https://benisnous.com/wp-content/uploads/2020/12/AWS-VPC-with-IPv6-DEMO-Egress-Only-Internet.jpg)
– shows hypervisor inventory of given VM controller
VPC MAC ADDRESS LEARNING SERIAL NUMBER
– shows VM controllers and their attributes such as IP/hostname, state, model, serial number – sets source and destination mac addresses – Tenant traceroute for vxlan encapped source EPĮLAM Setup and debugging (follow commands in order) – Tenant traceroute for vlan encapped source EP – shows the edge port config on the HIF (FEX) ports, the internal VLAN mapping and the STP TCN packet statistics received on the fabric ports – shows QoS counters for each class for all ports – shows QoS counters on each port (internal) – shows T2 TCAM entries for specified group – shows the QoS DSCP/dot1p policy configured for a vlan in HW – shows QoS classes configured in hardware – shows QoS classes/policices configured per vlan – CoPP statistics (red = dropped, green = allowed) – shows multicast route informatino in M2rib – shows multicast route information in M2rib MFDM gets (FD,port) memberships from vlan_mgr and uses this information go create BD floodlists. – shows IPv4 multicast routing table for given vrf IGMP uses this to get the groups on VPC and only sync them. – verify the tunnel to IF mapping in IGMP. Only when ports are part of BD joins are processed – verify BD membership of a port in IGMP. It needs to know the BD to create (BD, G)
![vpc mac address learning vpc mac address learning](https://benisnous.com/wp-content/uploads/2020/10/Change-MAC-address-of-virtual-machine.jpg)
– shows multicast router information IGMP – shows multicast route information in IGMP – shows IP multicast routing table for given vrf – more detailed than above command, specifically dealing with forwarding events and forwarding updatesįabric Multicast Debugging – L2 Multicast – shows isis multicast event history logs
VPC MAC ADDRESS LEARNING UPDATE
– shows topology and compute stats, MRIB update stats, Sync+Ack packet stats, Object store stats
![vpc mac address learning vpc mac address learning](http://www.vmwarearena.com/wp-content/uploads/2015/01/VMware-VM-MAC-Assignment_5-300x121.jpg)
– shows GIPO routes, Local/transit, OIF list – shows currecnt state of FTAG, cost, root port, OIF list – sets 4th register to select RFILDR selector (bit 13) & – setting register to specific trigger. – shows ASIC block counters for given ASIC. – provides isis tech-support output for TAC – shows all discovered tunnel end points – shows isis database, can also add detail – shows interface status information and statistics – RwEncapTable Indexed using the HigigDstMapTable’s result. – DstEncapTable Indexed using the HigigDstMapTable’s result. – HigigDstMapTable Indexed using DMOD/DPORT coming from T2. – shows next hops towards NorthStar ASIC or external router – shows bgp unicast routes for given vrf – shows bgp sessions/peers for given vrf Insieme ELTM VRF, VLAN, Interface Commands – EOBC/EPC switch status (0: EOBC, 1: EPC) – enables/disables given argument on all modules – show debug information for the diagnostic modules – shows diagnostic result of given test on given module – shows diagnostic result of given module or all modules – shows bootup tests and diagnostics of given module – Shows start and end dates of certificate. Cisco means new secure certs are installed, Insieme means old unsecure are installed – Next to PRINTABLESTRING, it will list Insieme or Cisco Manufacturing CA. – shows policy-element logs for SSL connectivityĬan also check logs in the /var/log/dme/log directory – tries to connect ssl between APIC and Node and gives output of SSL information wipeout will completely wipeout the node including configuration. – commissions, decommissions, or wipes out given node. – shows dhcp client information to confirm dhcp address from APIC – large output which will show cluster size, chassisID, if node is active, and summary of replica health – Factory resets APIC and after reboot will load into setup script – Decommissions the APIC of the given ID – shows the current cluster size and state of APICs
![Vpc mac address learning](https://knopkazmeya.com/1.png)